Logo Oventrop GmbH & Co. KG

Regudis W-HTE Electronic dwelling station
performance range 3, 25 l/min., heat exchanger copper brazed, with Sealix® protecitve layer


The Regudis W-HTE dwelling station with factory-preassembled electronic control and copper brazed stainless steel plate heat exchanger with protective layer enables the energy-efficient and hygienic supply of a dwelling with hot and cold potable water as well as heating water.

It is mounted on a thermally insulated lower shell for flush or surface wall mounting. The pipes are made of stainless steel 1.4404, the fittings of brass.
An optional thermal insulation reduces heat dissipation and prevents heating of the cold water by separating the hot and cold pipes. Insertable elements integrated in the upper thermal insulation shell allow recesses for the water meter, the heat meter, as well as the heat exchanger to ensure rapid cooling of the heat exchanger after a tapping process.
With the optional thermal insulation, the installation depth of 110 mm is not exceeded. All wetted parts on the potable water side are made of brass, stainless steel 1.4401 and 1.4404 and potable water approved plastics.

With an asymmetrical arrangement of the stainless steel plates of the heat exchanger, as well as a pressure loss-optimised design of the station, the station allows particularly efficient operation and enables hot water volume flows of 20-30 l/min (performance range 3) at excess temperatures of 0-15 K (according to SPF test procedure). This means that discharge capacities and excess temperatures can be individually adapted to the existing system parameters. The low excess temperatures make the station particulary suitable for operation in low temperature systems.

The adaptive electronic control independently adjusts to the operating conditions in the overall system. The set potable water temperature is constantly controlled, regardless of system temperatures, pressure loss ratios and required draw-off qunatities.
A demand-controlled priority circuit of the multifunctional control valve ensures intelligent energy distribution for hot potable water preparation as well as for the the heat supply of a residential unit.
In heating mode, the integrated differential pressure control of the control valve ensures efficient heat distribution between the stations. Hydronic balancing in the pipe network to the station is therefore unnecessary.
In the event of a power failure, a failsafe mode is activated. In failsafe mode, the actuator closes the control valve to prevent uncontrolled heating of the potable water.
A status LED indicates the current operating status of the station.

The copper brazed stainless steel heat exchanger features a protective layer on the primary and secondary sides. The optimised surface structure decreases the risk of calcification and reduces deposits. The media resistance on the primary and secondary side is improved. Due to the protective layer, the heat exchanger can be used in critical potable water regions with a high electrical conductivity >500 µS/cm and a chloride content >100 mg/l. An exact check of the materials that can be used is recommended on the basis of a potable water analysis and supplementary sheets provided by the manufacturer. The heat exchanger with protective layer also prevents metal migration into the potable water and heating water due to the surface with protective layer.

The Regudis W-HTE basic station can be individually extended with the following functions in a time-saving manner my means of a modular plug and play assembly concept:
  • Mixed heating circuit (flow temperature control module)
  • Simultaneous supply of an unmixed and a mixed heating circuit (heating circuit connection fitting)
  • Potable water circulation (potable water circulation module)
  • Electrical reheating of the potable water (instantaneous water heater module)
  • System separation of the heating circuit on the dwelling side from the heating circuit on the building side (Duo heating circuit separation module)
The Regudis W-HTE dwelling station consists of the following components:
  • Connection box for power supply 230 V AC, rated current 50 mA, output voltage 5 V DC, rated output current 1200 mA, protection type IP 65, protection class II, overvoltage category III, ambient temperature 0-60 °C
  • Actuator with integrated potable water temperature control 40-70 °C, max. ambient temperature 0-60 °C, power consumption 0.15-3 W, protection type IP 54, input voltage 5 V DC
  • Volume flow sensor (enables volume flow detection from 1 l/min)
  • Vent valve in the heating circuit
  • Multifunctional control valve for high flow rates with integrated differential pressure control valve and demand-controlled priority circuit for hot water preparation
  • Drain valve in the primary circuit
  • Zone valve for heating circuit control
  • Drain valve in the heating circuit with strainer
  • Copper brazed plate heat exchanger made of stainless steel 1.4401/1.4404 with protective layer
  • PT 1000 temperature sensor for hot water
  • Connection for potable water circulation module G 1
  • Spacer for heat meter G ¾, 110 mm
  • Spacer for water meter G ¾, 110 mm
  • Connection for derivative temperature control set M 22 x 1
  • Filter insert in the primary supply
  • Connection in the primary supply for the temperature sensor of the heat meter M 10 x 1.0
Performance data potable water:
Hot water capacity heat exchanger: 55-84 kW (performance range 3)
at 50-65 °C primary and 10 °C/50 °C secondary
Draw-off quantity: 20-30 l/min (according to SPF test procedure)
Pressure loss secondary: 300-650 mbar (without cold water meter)
3 ball valve connections DN 20

Performance data heating:
Heating output: 14 kW, delta T 20 K
max. 600 l/h
Max. differential pressure: 2.0 bar
Min. differential pressure: 150 mbar
Pressure loss primary: 150-250 mbar (without heat meter)
4 ball valve connections DN 20

General data:
Max. operating pressure: 10 bar
Tmax (primary): 90 °C
Ambient temperature: 2-35 °C
WxHxD (without ball valves): 600 x 455 x 110 mm
Centre distance to the connections: 65 mm
Centre distance to the wall: 26.5 mm
Weight: 10.2 kg

Extensive accessories:
Flow temperature control module for surface heating, heating circuit connection fitting, potable water circulation module, instantaneous water heater module, Duo heating circuit separation module, upper thermal insulation shell, derivative temperature control set, flushing and mounting bridge, earthing clamp, connection and shutoff set, flush-mounted cabinets, surface-mounted cabinets, revision frame, Regubox exclusive surface-mounted bonnet
Art.No.: 1344052
EAN: 4026755446944
Manufacturer: Oventrop GmbH & Co. KG
Subject to technical changes.

Accessories

Upper thermal insulation shell for Regudis W-HTE dwelling stations, EPP, anthracite
Item no. 1344470
Derivative temperature control set for Regudis W-HTE dwelling stations, thermostatically adjustable heating bypass
Item no. 1344490
Connection and shutoff set for Regudis W-HTE
Item no. 1344680
Connection and shutoff set for Regudis W-HTE with flushing function of the supply pipe
Item no. 1344685
Connection and shutoff set for Regudis W-HTE potable water circulation module
Item no. 1344684
Flushing and mounting bridge for Regudis W-HTE dwelling stations, for flushing the heating system
Item no. 1344489
Stainless steel spacer for Regudis W dwelling stations
Item no. 1349052
Earthing clamp for Regudis W dwelling stations
Item no. 1341092
Sealing plug set for Regudis W-HTE dwelling stations, 2-fold, for installation in a four-pipe system
Item no. 1344481
Heat meter connection set for Multidis SF and Regudis W-HTE with Hycocon VTZ double regulating valve DN 20, angle, ball valves DN 20
Item no. 1404578
Heat meter connection set for Multidis SF and Regudis W-HTE with Hycocon VTZ double regulating valve DN 20, angle, ball valves DN 25
Item no. 1404580
Heat meter connection set for Multidis SF and Regudis W-HTE with Hycocon DTZ differential pressure control valve DN 20, angle, ball valves DN 25
Item no. 1404682
Heat meter connection set for Multidis SFQ and Regudis W-HTE with ball valves DN 20, angle
Item no. 1405578
Heat meter connection set for Multidis SFQ and Regudis W-HTE with ball valves DN 25, angle
Item no. 1405580
Electrical connecting block for surface heating 6 control zones, heating, 24 V / 230 V
Item no. 1400980
ClimaCon F 210 Room thermostat for two-pipe applications, heating only/cooling only, leader 230 V AC
Item no. 1155021
Safety temperature monitor 20 °C - 90 °C
Item no. 1344583
Regtronic RH Weather-compensated heating circuit controller for mixed/unmixed heating circuit with 1 x outdoor sensor, 1 x pipe contact sensor and 2 x storage cylinder sensor
Item no. 1152083
Aktor M Motorized actuator, on/off and floating control 230 V AC, connection thread M 30 x 1.5
Item no. 1012729
Remote control with room temperature sensor suitable for Regtronic RH, RH-HT, EM, RM and RS controllers, sensor element PT 1000, surface mounting
Item no. 1152096
Electrical connecting block for surface heating 10 control zones, heating/cooling (change-over), pump and boiler control and integrated time switch, 230 V
Item no. 1400983
ClimaCon F 90 Room thermostat for two pipe applications, heating only/cooling only, follower 230 V AC
Item no. 1155009
Aktor T 2P Thermal actuator, on/off control 230 V AC, normally closed, connection thread M 30 x 1.5, cable length 2 m
Item no. 1012452
Regtronic RD-W System controller for the integration of the Regudis W dwelling stations into the heat supply with touch display
Item no. 1342093

OV Spare Parts Finder

Dimensions

Dimensions of article

Length Width Height Weight
110 mm 600 mm 455 mm 10,73 kg

Packing units

Type Qty. Length Width Height Weight
Carton 1 140 mm 490 mm 610 mm 12,15 kg
Europallet 10 1200 mm 800 mm 920 mm 128,32 kg

BIM/CAD

Download CAD-Formats
Format Size Download
Revit 468 KB
Download
DWG (3D) 32,44 KB
Download
DWG 12,46 KB
Download
DXF (3D) 218,69 KB
Download
DXF 15,42 KB
Download
STEP 114,61 KB
Download
OBJ / MTL 17,58 KB
Download

Notice for CAD viewer

In order to open the CAD-Viewer and Download CAD-Data please onetime download and install the CAD-App.

Images

Product images

  File size
2,3 MB
  Size
5000 px x 5000 px
  Properties
  •  Clear product picture
  •  Cutout
Download
  File size
2,13 MB
  Size
5000 px x 5000 px
  Properties
  •  Clear product picture
  •  Cutout
Download
  File size
1,03 MB
  Size
4096 px x 4096 px
  Properties
  •  Clear product picture
  •  Cutout
Download
  File size
967,77 KB
  Size
4096 px x 4096 px
  Properties
  •  Clear product picture
  •  Cutout
Download
  File size
1018,04 KB
  Size
4096 px x 4096 px
  Properties
  •  Clear product picture
  •  Cutout
Download
  File size
1,15 MB
  Size
4096 px x 4096 px
  Properties
  •  Clear product picture
  •  Cutout
Download

Dimensional drawings

  File size
47,3 KB
  Size
560 px x 811 px
  Properties
  •  Clear product picture
  •  Cutout
Download

Drawings

  File size
31,09 KB
  Size
425 px x 425 px
  Properties
  •  Clear product picture
  •  Cutout
Download

Documents

Circuit diagram

  Name Size
more languages 286,61 KB
more languages 295,16 KB
more languages 326,27 KB
more languages 334,98 KB
more languages 95,83 KB
more languages 108,81 KB
more languages 278,93 KB
more languages 286,74 KB
more languages 317,16 KB
more languages 323,73 KB

ETIM

Klassifizierung
ETIM 7.0
Property Value
Width 600 mm
Model Indirect
Height 455 mm
Depth 110 mm
Suitable for CH/tap water
With adapter for heat meter
With heat meter
Adjustment range hot water temperature 40 - 70
Nominal internal diameter hot tap water 3/4 inch (20)
Nominal inner diameter cold tap water 3/4 inch (20)
Tap capacity at 60°C, continuous 25 l/min
Max. operating pressure 10 kPa
Exchanger with dual separation
Nominal inner diameter heating 3/4 inch (20)
Nominal inner diameter of supply 3/4 inch (20)
Nominal inner diameter return 3/4 inch (20)